258 koa speer electronics, inc. ? 199 bolivar drive ? bradford, pa 16701 ? usa ? 814-362-5536 ? fax: 814-362-8883 ? www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. 2/24/08 emi/emc filtering features ? noise suppression in signal i/o lines and other circuits that require multiple chip beads for noise suppression ? multiple circuits in a single package ? marking: black body color with no marking ? products with lead-free terminations meet eu rohs requirements fba ferrite bead array dimensions and construction w t a l b p protective coating solder plating l .126.008 (3.20.2) .063.008 (1.60.2) .031.008 (0.80.2) .031.008 (0.80.2) .016.008 (0.400.2) .012.008 (0.30.2) wt ab p dimensions inches (mm) ordering information 1j: 0603 te: 7" embossed plastic (3,000 pieces/reel) fba type size impedance packaging new part # 1j number of circuits circuits 4 a: standard b: high speed characteristics a te 300 tolerance p for further information on packaging, please refer to appendix a. p: 25% 2 significant figures + 1 multiplier ex: 300 = 30 ? type 1j (0603) (inch size code) t: sn termination material t circuit schematic eu 1733 reader's spreadspg189-328:1570 reader's spreadspg189-328 1/27/09 4:59 pm page 63
fba ferrite bead array leach resistance appearance: there shall be no visible signs of physical or mechanical damage (i.e. no cracks). terminations: termination must not be leached away for more than 5%. the bead shall be subjected to the following 5 steps for the period of time shown below. the 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) flux: 5 - 10 seconds 2) after flux: air dry for 15 seconds 3) solder temperature: 230c 5c 4) dip time: 5 0.5 second 5) cool: air cool for 60 seconds environmental applications performance characteristics parameter operating temperature -55c to +125c storage temperature 40c @ 70% humidity sealed plastic bags with desiccant shall be used to reduce the potential of oxidation on the terminations during storage. resistance to solder heat change in impedance: relative to value before test 20% appearance: there shall be no cracking. solder coverage: more than 75% of the terminal electrode shall be covered with solder. flux: 5 - 10 second dip after flux: air dry for 15 seconds preheat: 150c 10c preheat time: 60 seconds solder temperature: 260c 5c dip time: 10 1 second solderability solder coverage: more than 95% of the termination shall be covered with solder. flux: 5 - 10 second dip after flux: air dry for 15 seconds solder temperature: 245c 5c dip time: 5 0.5 second requirement test method pms 300 neg. black neg. 259 koa speer electronics, inc. ? 199 bolivar drive ? bradford, pa 16701 ? usa ? 814-362-5536 ? fax: 814-362-8883 ? www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. 3/05/07 emi/emc filtering applications and ratings part designation impedance @ 100mhz (?) dc resistance maximum (?) allowable dc current per element maximum (ma) operating temperature range fba1j4atte300p 30 fba1j4atte600p 60 fba1j4atte121p 120 FBA1J4ATTE221P 220 fba1j4atte301p 300 fba1j4atte601p 600 fba1j4atte102p 1000 fba1j4btte300p 30 fba1j4btte600p 60 fba1j4btte121p 120 fba1j4btte221p 220 fba1j4btte301p 300 fba1j4btte601p 600 0.1 0.25 0.3 0.4 0.5 0.7 0.25 0.3 0.4 0.45 0.50 0.65 200 400 350 250 100 200 400 350 100 150 100 -55c to +125c new new 1733 reader's spreadspg189-328:1570 reader's spreadspg189-328 1/27/09 4:59 pm page 64
260 koa speer electronics, inc. ? 199 bolivar drive ? bradford, pa 16701 ? usa ? 814-362-5536 ? fax: 814-362-8883 ? www.koaspeer.com specifications given herein may be changed at any time without prior notice. please confirm technical specifications before you order and/or use. 3/01/07 fba ferrite bead array environmental applications (continued) performance characteristics parameter terminal strength (hanging test) appearance: the terminal electrode shall not break off, nor shall there be damage to the body. type: w(kgf): time: 1206 1.5 30 seconds 2 seconds terminal strength (push test) appearance: there shall be no evidence of mechanical degradations to terminals or body. type: w(kgf): time: 1206 2.3 60 seconds solvent resistance change in impedance: relative to value before test 10% cleaning by: washer: ultrasonic washer (100w) solvent: isopropyl alcohol time: 3 minutes insulation resistance insulation resistance: min. 1g ohms requirement test method bending strength appearance: there shall be no physical or mechanical damage. impedance: relative to initial value before test 10% board: 90 x 40 x 1.6mm bend: 1mm time: 5 sec mechanical shock appearance: there shall be no physical or mechanical damage. impedance: relative to initial value before test 10% force: 50g time: 11 msec there shall be 3 shocks in each of 6 directions (18 shocks total) vibration impedance: relative to initial value 10% only endurance conditioning by sweeping shall be made. the entire frequency range from 10 - 2,000 hz, return to 10 hz in 20 minutes (this will constitute one cycle). amplitude: 15g the test shall have a 15g peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 mutually perpendicular directions (a total of 36 cycles within a total of 12 hours). thermal shock appearance: there shall be no physical or mechanical damage. impedance: relative to initial value 20% dcr: the dcr shall not exceed initial specified value. testing of the parts will be made at 0 hours, 250 hours and 500 hours. before testing, the parts shall be allowed to cool to room temperature for 24 hours. step: temperature: time: 1-start -40c 2c 2-hold -40c 2c 30 minutes 5 minutes 3-transfer 0.5 minutes maximum 4-hold 105c 2c 30 minutes 5 minutes 5-transfer 0.5 minutes maximum steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. load humidity appearance: there shall be no physical or mechanical damage. impedance: relative to initial value 15% measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. temperature: 85c 2c relative humidity: 85% time: 1,000 hours total apply: 100% rated current life test appearance: there shall be no physical or mechanical damage. impedance: relative to initial value 15% measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. temperature: 85c 2c time: 1,000 hours total apply: 100% rated current emi/emc filtering 1733 reader's spreadspg189-328:1570 reader's spreadspg189-328 1/27/09 4:59 pm page 65
|
